Processing / Network	Lake / Dante
Number of amplifier channels	4
Total burst power all channels (share among channels with RPM)	12000 W

2 ohms	3000 W
2.67 ohms	3000 W
4 ohms	3000 W
8 ohms	1900 W
16 ohms	950 W
Hi-Z 70 V	3000 W
Hi-Z 100 V	3000 W

4 ohms	6000 W
8 ohms	6000 W
16 ohms	3800 W

2 ohms	4400 W
2.67 ohms	5900 W
4 ohms	4600 W
8 ohms	2300 W
16 ohms	1150 W
Hi-Z 70 V	3300 W
Hi-Z 100 V	4700 W

Peak output voltage	194 V
Max output current	67 A
Rational Power Management (RPM)	Share “total burst power” of the product freely among channels. Any channel can scale up to the “Max. output power single channel”
Default voltage limitation (can be lifted with RPM configuration)	175 V
Protection features	Current Average Limiter (CAL), Very High Frequency Protection (VHF), Direct Current Protection (DC), Short Circuit Protection, Current-Clip Limiter, Voltage Clip Limiter, Temperature protection

Inter Sample Voltage Peak Limiter (ISVPL)	Configurable Peak voltage threshold and profile
Amplifier gain	Digital configurable amplifier gain 22 - 44 dB
Pilot tone generation and analysis	LoadPilot
Load impedance analysis	Yes
Temperature control	Regulated fans and show must go on limitation (ATL, PTL)

THD + N 20 Hz - 20 kHz for 1 W	< 0.05 %
THD + N at 1 kHz and 1 dB below clipping	< 0.04 %
Dynamic range	> 114 dB
Channel separation (Crosstalk) at 1 kHz	> 70 dB
Frequency response (1 W into 8 ohm, 20 Hz - 20 kHz)	+/- 0.05 dB
Internal sample rate / Data path	48 / 96 kHz / 32 bit floating point
Product propagation delay AES 96 kHz / analog input	1.61 / 1.68 ms

Loudspeaker processing	Up to 4 modules of Classic/linear-phase/FIR crossover, EQ, delay, LimiterMax™ - peak and RMS limiters
System tuning	Group control with Raised Cosine™ MESA EQ™ asymmetric filters
Input redundancy / Matrix	Automatic 4 level input redundancy / 4 input mixers
System integration	Comprehensive 3rd party protocol over UDP Ethernet

Dante I/O	8 x 8 (shared with AES67)
Network topology / redundancy	Flexible topology / Supports daisy-chained and Dual redundant networks
Sample rates / transport	48, 96 kHz / Uni + Multicast
Network latency	0.25, 0.5, 1.0, 2.0, 5.0 ms

I/O	8x8 (shared with Dante)
Network topology / redundancy	Flexible topology / supports daisy-chained networks
Sample rates / transport	48 kHz / Multicast
Network latency	2 ms

Inputs	4 high quality inputs with Iso-Float ground isolation
Maximum input / digital reference	+ 26 dBu / +21 dBu
Sampling rate / resolution	96 kHz / 24 bit
Input impedance balanced / unbalanced	20 / 10 kOhm
THD + N (typical at 1 kHz unweighted)	2.2E-6
THD + N (typical at 20 Hz and 20 kHz unweighted)	3.3E-6

Inputs	2 AES inputs (4 audio channels)
Supported sample rates / resolution	44.1, 48, 88.2, 96, 176.4, 192 kHz / up to 24 bit
Sample rate conversion THD + N 20 Hz - 20 kHz unweighted	3.0E-7

Analog inputs	4 x Terminal block connectors along input with +, – and ground
AES inputs	2 x Terminal block connectors
Output connectors	4 x 2 pole Terminal block connectors rated at 1000 V / 76 A (exceeding amplifi er capacity) Can take up to 16 mm2 (6 AWG) cables
Ethernet ports	2 x EtherCon RJ45 100/1000 Base–T for the Lake Controller, Dante controller and/or DLM (3rd party protocol)
Detachable mains cord	Neutrik PowerCon rated at 250 V / 32 A

System status indication	3 x tri-color LED. FRAME, TEMP, PSU for device status indication
Channel status indication	3 x tri-color LED per channel. Status indication separated for channel LOAD, AMP, SIGNAL status
Mute	Per channel touch button for MUTE control and tri-color LED for indication
Power	Touch button for ON/STANDBY control and tri-color LED for power state indication
Select	Touch button and LED for bi-directional device software select functionality

Nominal voltage	100 – 240 V AC 50 – 60 Hz
Operating voltage	70 – 265 V AC 45 – 66 Hz
Mains wall plug	Selectable on order CEE 7/7 “Schuko” 230 V / 16 A, NEMA L5–30 “Twistlock” 125 V / 30 A, NEMA 5–15P 125 V / 15 A (D 80:4 only), NEMA 5–20P 125 V / 20 A (D120:4 only), NEMA 6–20P 250 V / 20 A, AS/NZS 3112 230 V / 15 A (Aus/Nz), BS 546 230 V / 16 A (India), C–30P 125V / 30A (Japan)

Soft start / Inrush power	Yes / Max 8 A
Power factor correction	> 0.98 for mains power > 400 W
Regulated switch mode power supply (R.SMPS)	Yes
Breaker Emulation Limiter (BEL)	Configurable current threshold and breaker profile
BEL max current threshold	25 A
Power Average Limiter (PAL)	Yes
Under Voltage Limiter (UVL)	Yes
Mains undervoltage and overvoltage protection and mains glitch tolerance	Yes

Rack rail to rear panel	W: 483 mm (19”), H: 88 mm (2 U), D: 424 mm (16”)
Overall all depth front–rear support	D: 463 mm
Weight	15.8 kg
Finish	Black painted steel chassis with grey painted steel front with detachable grille
Approvals	CE, ETL (ANSI/UL, CSA), PSE, RCM