Processor	1 x Analog Devices SHARC 21489 @ 400 MHz SIMD
Raw Processing Capacity	400 MIPS, 1.6 GFLOPS
Sampling Rate	48 kHz
Frequency Response (A/D/A)	20 Hz – 20 kHz, ± 0.5 dB
Dynamic Range (A/D/A)	> 113 dB, A-weighted
THD + Noise	< 95 dB (22.4 kHz BW, un-weighted); 1 kHz @ +15 dBu with 0 dB gain
Channel Separation (A/D/A)	> 110 dB @ 1 kHz, +24 dBu
Latency (A/D/A)	1.04 mS, inputs routed to outputs
Delay Memory	174 mono seconds
Analog Control Inputs	0-3.3 VDC
Recommended External Control Potentiometer	10k Ohm, linear
Logic Outputs	Low (0 V) when active, pulled high (5 V) when inactive
Logic Output Maximum External Power Supply Voltage	24 VDC
Logic Output Maximum External Power Supply Current Sinking	50 mA
Logic Output Maximum Output Current	10 mA
RS-485 Serial I/O	38.4 kbaud (default) 8 data bits, 1 stop bit, no parity, no flow control. May be broken out of ARC port
Ethernet Cable	Standard CAT5e or CAT6, maximum device-to-device length = 100 m
Dante Cable	Standard CAT6, maximum device-to-device length = 100 m
ARC Cable	Standard CAT5, distance dependent upon load and number of devices. 8 Watts maximum power available
Maximum Devices Per System	128 units per Site File
Maximum Stored Presets	1000

Number of Inputs	Sixteen (16) switchable balanced mic or line level
Connectors	3.81 mm terminal blocks
Nominal Input Level	+4 dBu
Maximum Input Level	+23 dBu
Mic Pre-amp Gain	0, 12, 24, 44, or 54 dB switchable with ± 24 dB trim
Mic Pre-amp EIN	< -125 dB with 150 Ohm source impedance. 22.4 kHz BW
CMRR	> 79 dB @ 1 kHz, unity gain
Input Impedance	8k Ohms balanced, 4k Ohms unbalanced
Phantom Power	+48 VDC, 10 mA maximum (per input)
Dynamic Range	> 113 dB, A-weighted
THD + Noise	< -100 dB; 22.4 kHz BW, unweighted; 1 kHz @ +15 dBu with 0 dB gain. Course gain is set to +4 dBu
A to D Latency	0.28 mS
Number of Outputs	Sixteen (16) balanced line level
Connectors	3.81 mm terminal blocks
Nominal Output Level	+4 dBu with 20 dB of headroom
Maximum Output Level	+24 dBu (+22.8 dBu into a 2k Ohm minimum load)
Output Impedance	300 Ohms balanced, 150 Ohms unbalanced
Dynamic Range	> 117 dB, A-weighted
THD + Noise	< -97 dB; 22.4 kHz BW, unweighted; 1 kHz, 0 dB gain +8 dBu output
D to A Latency	0.60 mS

Space Required	1U (WDH: 18.91 in. x 9.88 in. x 1.72 in. / 48.02 cm x 25.1 cm x 4.37 cm). Depth does not include connector allowance. Allow at least 3 inch additional clearance for rear panel connections. Additional depth may be required depending upon your specific wiring and connections.
Electrical	24V 1.4A, 34W maximum. Symetrix Part Number 12-0034. CUI part number SDI65-24-U-P5.
Ventilation	Maximum recommended ambient operating temperature is 30 C / 86 F. Ensure that the left and right equipment sides are unobstructed (5.08 cm, 2 in minimum clearance). The ventilation should not be impeded by covering the ventilation openings with items such as newspapers, tablecloths, curtains, etc.
Shipping Weight	9.4 lbs (4.2 kg)
Certifications and Compliance	IEC 62368-1, EN 55032, EN 55103-2, FCC Part 15, ICES-003, UKCA, EAC, RoHS (Health/Environmental)

Processor	1 x Analog Devices SHARC 21489 @ 400 MHz SIMD
Raw Processing Capacity	400 MIPS, 1.6 GFLOPS
Sampling Rate	48 kHz
Frequency Response (A/D/A)	20 Hz – 20 kHz, ± 0.5 dB
Dynamic Range (A/D/A)	> 113 dB, A-weighted
THD + Noise	< 95 dB (22.4 kHz BW, un-weighted); 1 kHz @ +15 dBu with 0 dB gain
Channel Separation (A/D/A)	> 110 dB @ 1 kHz, +24 dBu
Latency (A/D/A)	1.04 mS, inputs routed to outputs
Delay Memory	174 mono seconds
Analog Control Inputs	0-3.3 VDC
Recommended External Control Potentiometer	10k Ohm, linear
Logic Outputs	Low (0 V) when active, pulled high (5 V) when inactive
Logic Output Maximum External Power Supply Voltage	24 VDC
Logic Output Maximum External Power Supply Current Sinking	50 mA
Logic Output Maximum Output Current	10 mA
RS-485 Serial I/O	38.4 kbaud (default) 8 data bits, 1 stop bit, no parity, no flow control. May be broken out of ARC port
Ethernet Cable	Standard CAT5e or CAT6, maximum device-to-device length = 100 m
Dante Cable	Standard CAT6, maximum device-to-device length = 100 m
ARC Cable	Standard CAT5, distance dependent upon load and number of devices. 8 Watts maximum power available
Maximum Devices Per System	128 units per Site File
Maximum Stored Presets	1000

Number of Inputs	Sixteen (16) switchable balanced mic or line level
Connectors	3.81 mm terminal blocks
Nominal Input Level	+4 dBu
Maximum Input Level	+23 dBu
Mic Pre-amp Gain	0, 12, 24, 44, or 54 dB switchable with ± 24 dB trim
Mic Pre-amp EIN	< -125 dB with 150 Ohm source impedance. 22.4 kHz BW
CMRR	> 79 dB @ 1 kHz, unity gain
Input Impedance	8k Ohms balanced, 4k Ohms unbalanced
Phantom Power	+48 VDC, 10 mA maximum (per input)
Dynamic Range	> 113 dB, A-weighted
THD + Noise	< -100 dB; 22.4 kHz BW, unweighted; 1 kHz @ +15 dBu with 0 dB gain. Course gain is set to +4 dBu
A to D Latency	0.28 mS
Number of Outputs	Sixteen (16) balanced line level
Connectors	3.81 mm terminal blocks
Nominal Output Level	+4 dBu with 20 dB of headroom
Maximum Output Level	+24 dBu (+22.8 dBu into a 2k Ohm minimum load)
Output Impedance	300 Ohms balanced, 150 Ohms unbalanced
Dynamic Range	> 117 dB, A-weighted
THD + Noise	< -97 dB; 22.4 kHz BW, unweighted; 1 kHz, 0 dB gain +8 dBu output
D to A Latency	0.60 mS

Space Required	1U (WDH: 18.91 in. x 9.88 in. x 1.72 in. / 48.02 cm x 25.1 cm x 4.37 cm). Depth does not include connector allowance. Allow at least 3 inch additional clearance for rear panel connections. Additional depth may be required depending upon your specific wiring and connections.
Electrical	24V 1.4A, 34W maximum. Symetrix Part Number 12-0034. CUI part number SDI65-24-U-P5.
Ventilation	Maximum recommended ambient operating temperature is 30 C / 86 F. Ensure that the left and right equipment sides are unobstructed (5.08 cm, 2 in minimum clearance). The ventilation should not be impeded by covering the ventilation openings with items such as newspapers, tablecloths, curtains, etc.
Shipping Weight	9.4 lbs (4.2 kg)
Certifications and Compliance	IEC 62368-1, EN 55032, EN 55103-2, FCC Part 15, ICES-003, UKCA, EAC, RoHS (Health/Environmental)